Balboa Series
™
SUB10
Powered Subwoofer
Service Manual
JBL Consumer Products 250 Crossways Park Dr.
Woodbury, New York 11797
Rev0 10/2006
BALBOA series SUB10
- CONTENTS -
BASIC SPECIFICATIONS …………….……..…………..1 PACKING……..………………….….….…………..……...2 DETAILED SPECIFICATIONS ……….……..…………..3 CONNECTIONS………………………...……..…...…..…5 OPERATION ……..………………….……...…….….…...7 TEST SET-UP AND PROCEDURE….…………………..8 EXPLODED VIEW/PARTS LIST…………………………9 AMPLIFIER BLOCK DIAGRAM…………………………10 DETAILED TROUBLESHOOTING……………………..12 ELECTRICAL PARTS LIST ..……….……….……….…13 P.C.B. DRAWINGS……………………………………….17 IC/TRANSISTOR PINOUTS..……..….…….….….….….23 SCHEMATICS……………………….……………………24
BALBOA SUB10 SPECIFICATIONS
Amplifier Power (RMS): 100 Watts Peak Dynamic Power *: 225 Watts Driver: 10\" (254mm) Inputs: Line Level and LFE Crossover Frequency: Frequency Response: Dimensions (H x W x D):
Variable from 50Hz to 150Hz, 24 dB per octave 30Hz – 150Hz
19-3/4\" x 14-1/16\" x 14-3/4\" (502mm x 357mm x 375mm)
Weight: 35 lb/16kg
JBL continually strives to update and improve existing products, as well as create new ones. The
specifications and details in this and related JBL publications are therefore subject to change without notice.
* The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the output of a resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off.
1
BALBOA series SUB10
2
BALBOA series SUB10
Balboa Sub 10
LINE VOLTAGE
US 120VAC/60HzEU 230VAC/50-60Hz
100W Powered Sub/ Plate Amp
Yes/NoYesYes
Hi/Lo Line108-132207-254
UnitVrmsVrms
Notes
Normal OperationNormal Operation
Normal operation, MOMS required
Parameter
Amp Section
Type (120V Model)Type (230V Model)
Load Impedance (speaker)
SpecificationUnitQA Test LimitsConditionsNotes
AB G4ABHOhmsN/AN/AN/A
120V System is Class AB230V System is Class G
Nominal
Measured with AP using the ratio
method, sweeping with an ext. amp 10 to Average on the operating BW from 10 to 500 Hz500Hz@ Nominal input voltage @ Nominal input voltage
3/20 50 Hz Burst unit driven 6dB above the sensitivity to drive it into max power,
measured value is the average of the 4 first
@ Nominal input voltage consecutive peaks
Highest RMS of the first 4 consecutive
@ Nominal input voltage peaks22K filter22K filter
@ Speaker OutputMeasured at amplifier board speaker out terminals, Output power 90 Watts THD <
0.1 %
System average impedanceRated Output Power 120VRated Output Power 230V8.2100105OhmsWattsWattsReference
95100
Avgerage value - RMS Dynamic powerDynamic power HPTHD@ Rated PowerTHD @ 1 WattDC OffsetDamping factor
Input SensitivityInput FrequencyLine Input (L&R)LFE Input
System Gain-L and R inputsSignal to NoiseSNR-A-WeightedSNR-unweighted
SNR @ 1W-unweightedResidual Noise FloorInput ImpedanceLine input L&R , LFEFilters
Low Pass (fixed or variable)Subsonic filter (HPF)Friend circuit
Limiter (yes/no)
THD at Max. Output PowerFeaturesLFE Input
Phase Switch (yes/no)Volume pot Taper (lin/log)LP Variable Crossover controATO
Input ConfigurationLine In (L,R)Line level in LFESignal Sensing (ATO)Auto-Turn-On (yes/no)ATO Input FrequencyATO Level Line Level in (L,R1031340.50.110>150
WattsWatts%%mV-DCDF
ReferenceReference
10.350100
50159.542.27HzmVrmsmVrmsdB50±2dB±2dB±2dBNominal Freq.To 1 WattTo 1 WattGain=130
Single input driven 1 input drivenLFE input driven only
Single input driven L or R
9085651
dBAdBrdBr
mVrms(max)
8580601.5
To Rated power To Rated power To 1 Watt
Volume @max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics)
A-Weighting filter22KHz filter22KHz filter
>10K ohmsN/ANominal over the audio BWReference only
VariableFixedFixedYESN/A
--
±2dB±2dB±2dBN/AN/A
2nd order variable + 2nd order fix, Range 50-110 Hz
----
YESYESLOGYESYES
----
Functional Functional Functional
Functional Range 50-110 HzFunctional fsBW Limited to 500 Hz,
L ,RLFE
--
FunctionalFunctional
RCA inputs: RED-WHT, L , R Summed to Mono
Single connector
YES501.5
--HzmV
FunctionalFunctionalFunctional
2mV@50Hz into Line Input w/ 1 ch. driven
3
BALBOA series SUB10
Parameter
Unit
Conditions
Notes
SpecificationQA Test Limits
ATO Turn-on time
Auto Mute/ Turn-OFF TimePower on Delay timeTransients/PopsATO TransientTurn-on TransientTurn-off TransientEfficiency
< 1103
Secminutessec.
FunctionalFunctionalFunctional
Amp connected and AC on, then input signal applied
T before muting, after signal is removedAuto turn of time (T) must be 5 > T <15AC Power Applied
55050mV-peakmV-peakmV-peak10100100@ Speaker Outputs@ Speaker Outputs@ Speaker Outputs
AC Line cycled from OFF to ONAC Line cycled from ON to OFF
Stand-by Input Power
Power Cons/Amps.@rated power 120V Model
Power Cons/Amps.@rated power230V ModelProtection
Short Circuit Protection Thermal Protection DC Offset ProtectionLine Fuse Rating120VAC230VAC
13192 / 1.89 208 / 1.1
WattsWatts/AmpsWatts/Amps
14208 / 2.00210 / 1.2
@ nom. line voltage Unit active, no signal applied (Green LED)@ 120V-60 Hz (Nom.line voltage)@ 230V-50 Hz (Nom.line voltage)
Maximum allowable input power under nominal Input voltage and frequency, HOT or COLD operation.
100 Watts @ 4 Ohms nominal line voltage100 Watts @ 4 Ohms nominal line voltage
YES65 deg. CYES2.51.25
------AmpsAmps
FunctionalFunctionalFunctional
Direct short at output
@1/8 max unclipped Power
DC present at Speaker Out leadsType-T or Slo BloType-T or Slo Blo
Temperature rise should not exceed 35K rise
Relay or crowbar (for driver/fire protection)External fuse with UL/SEMKO rated holderExternal fuse with UL/SEMKO rated holder
4
BALBOA series SUB10 CONTROLS AND CONNECTIONS
Rear Panel
AHarman International®Company¡™£¢∞§¶FUSEAC~T2.5A L 250V120VTYPE60HZ200 Watts5
0Subwoofer-Level Control 1Crossover Adjustment2Phase Switch3LFE Input4Line-Level Inputs 5Power Indicator LED6Power Switch
BALBOA series SUB10 SUBWOOFER CONNECTIONS
Choose the Subwoofer ConnectionThat Is Most Suitable for YourReceiver/Processor
If you have a Dolby®Digital or DTS®receiver/processor with a low-frequency-effects (LFE) or subwoofer output:
SUBWOOFER ORLFE OUTPUT
If your receiver/processor does not contain a Dolby Digital or DTSprocessor but has a subwoofer output:
LRNOTE: Some receivers have one subwoofer output.
In that case, it is recommended that you use a Y connector (not included)to maximize performance.
6
BALBOA series SUB10 OPERATION
Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use theoutlets on the back of the receiver.
Initially set the Subwoofer-Level Control ¡to the “min” position.Turn on your sub by pressing the Power Switch ¶on the rear panel.Turn on your entire audio system and start a CD or movie soundtrackatamoderate level.
Auto On/Standby
With the Power Switch ¶inthe ON position, the LED §onthe rearpanel will remain lit in red or green to indicate the On/Standby modeofthe subwoofer.
RED = STANDBY (no signal detected, amp off)GREEN = ON (signal detected, amp on)
The subwoofer will automatically enter the Standby mode afterapproximately 10 minutes when no signal is detected from yoursystem. The subwoofer will then power ON instantly when a signal is detected. During periods of normal use, the Power Switch ¶can be left on. You may turn off the Power Switch ¶for extendedperiods of nonoperation, e.g., when you are away on vacation.Adjust Level
Turn your Subwoofer-Level Control ¡up to the “5” position(halfway). If no sound emanates from the subwoofer, check the AC-line cord and input cables. Are the connectors on the cablesmaking proper contact? Is the AC plug connected to a “live”receptacle? Has the Power Switch ¶been pressed to the “On”position? Once you have confirmed that the subwoofer is active,proceed by playing a CD, record or cassette. Use a selection that has ample bass information.
Set the overall volume control of the preamplifier or stereo to acomfortable level.Adjust the Subwoofer-Level Control ¡until you obtain a pleasing blend of bass. Bass response should not
overpower the room but rather be adjusted so there is a harmoniousblend across the entire musical range. Many users have a tendencyto set the subwoofer volume too loud, adhering to the belief that asubwoofer is there to produce lots of bass. This is not entirely true. Asubwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. However,overall balance must be maintained or the music will not soundnatural. An experienced listener will set the volume of the subwooferso its impact on bass response is always there but never obtrusive.
7
Phase Control
The Phase Switch £determines whether the subwoofer speaker’spiston-like action moves in and out with the main speakers (0˚), oropposite the main speakers (180˚).Proper phase adjustment dependson several variables such as room size, subwoofer placement andlistener position. Adjust the phase switch to maximize bass output at the listening position.
Crossover Adjustments
The Crossover Adjustment Control ™determines the highestfrequency at which the subwoofer reproduces sounds. If your mainspeakers can comfortably reproduce some low-frequency sounds,set this control to a lower frequency setting, between 50Hz and100Hz. This will concentrate the subwoofer’s efforts on the ultradeepbass sounds required by today’s films and music. If you are usingsmaller bookshelf speakers that do not extend to the lower bassfrequencies, set the Crossover Adjustment Control to a highersetting, between 120Hz and 150Hz.
NOTE:This control will have no effect if the LFE Input ¢is used. Ifyou have a Dolby Digital or DTS processor/receiver, the Low-PassFrequency is set by the processor/receiver. Consult your owner’smanual to learn how to view or change this setting.
BALBOA series SUB10
BALBOA SUB10 Test Set Up and Procedure
SYSTEM AURAL SWEEP TEST Equipment needed:
• Function/signal generator/sweep generator • Integrated Amplifier • Multimeter
• Speaker cables
General Unit Function (UUT = Unit Under Test)
Switches/knobs on the amplifier faceplate:
Low Pass Frequency Adjust full CW (150Hz) Phase switch – either position
1. From the signal generator, Connect both right and left line level inputs (RCA) – not the LFE jack - to signal
generator and UUT. Use Y-cable if necessary from mono source. 2. On the amplifier, turn the LEVEL control full Counterclockwise (Min). 3. Turn on generator, adjust to 100mV, 50 Hz.
4. Plug in UUT; turn the power switch ON. Turn LEVEL control full Clockwise (Max).
5. LED should now be Green; immediate bass response should be heard and felt from rear port tube opening. 6. Turn off generator, turn LEVEL control fully Counterclockwise (Min), disconnect RCA cable.
Sweep Function
1. Follow steps 1-6 above, using a sweep generator as a signal source.
2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofer and test.
Driver Function (Woofer)
1. Remove woofer from cabinet; detach + and - wire clips.
2. Check DC resistance of woofer; it should be 3.3 ohms ±10%.
3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated
amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
8
BALBOA series SUB10
EXPLODED VIEW
9
BALBOA series SUB10
10
BALBOA series SUB10
11
BALBOA series SUB10
BALBOA SUB10 (UL) AMP Troubleshooting Flow Chart
AMP no signal out no Check Fuse,Transformer, yes D110, etc Dc voltage check ±Vcc yes yes no Check Q117,118,119,D109 etc Check+/-15VDC yes yes LED red Led light green or red Check,Q206,Q207,U203 etc LED light green yes yes CheckU201,U202,VR201 Check U201 no VR202. etc Check U202 pin14 signal pin14 signal yes yes no no Check limiter board C304 Check U301,R343,R344 ,C340,Q301,Q302, etc yes yes yes Check ,+VCC& -VCC no DC voltage Check J123,J124 etc Test R121,R122 signal no yes yes Check Q107,Q108,Q105, Check RY101,D102,Q113,Q114 etc Q106,Q103,Q104,U101,etc yes no Check U101,Q115,Q116,R138 etc Set R138 to R140’S Voltage is 0.51VDC yes yes The Amp ass’Y OK, END Check P102 signal
12
BALBOA series SUB10
Balboa SUB10 (120v) Electrical Parts ListPart NumberDescriptionQtyReference DesignatorPOWER/MAIN PCBResistors110-14472j26-e110-14681j26-e110-16101j26-e110-16102j26-e110-16103j26-e110-16105j26-e110-16123j26-e110-16152j26-e110-16153j26-e110-16154j26-e110-16181j26-e110-16182j26-e110-16223j26-e110-16332j26-e110-16392j26-e110-16393j26-e110-16470j26-e110-16471j26-e110-16472j26-e110-16473j26-e110-16560j26-e110-16563j26-e110-16682j26-e110-10821jk2-e110-122r2j15-e110-20331jk2-e113-50r10j10-e114-03302m0-eCapacitors130-2b102k503-e130-3f104z503-e130-3f473m503-e130-sl101k503-e132-104j503-e132-223ja03-e135-3105m50-e135-3107m16-e135-3226m50-e135-3227m10-e135-3227m16-e135-3476m25-e132-223ja03-e135-3107m16-e135-4688m50-eSemiconductors192-027c1815gr-e192-028a1015gr-e192-1572n5551-e192-1582n5401-e197-031n4148-e199-15000335-e199-15000625-e199-15001605-etransistor 2SC1815GR TOSHIBA(RoHS) NPNtransistor 2SA1015GR TOSHIBA(RoHS) PNP*transistor FSC 2N5551 (RoHS) NPNtransistor FSC 2N5401 AI-PNP 350V 500mA TO-92 (RoHS) PNPdiode 100mA 75V SIGNAL 1N4148 ROHM (RoHS)zener diode 3.3V 1/2W 52mm (RoHS)zener diode HZ6C2 RENESAS (RoHS)zener diode HZ16-2 RENESAS (RoHS)52224121Q102,Q111,Q112,Q113,Q118,Q114,Q116,Q103,Q109,Q104,Q110,D101,D103,D105,D108,D102,D106,D107,D109,disc capacitor 1000P 50V ±10% (RoHS)disc capacitor 0.1U 50V +80/-20% (RoHS)disc capacitor 0.047U 50V ±20% (RoHS)disc capacitor 100P 50V SL ±10% (RoHS)mylar capacitor 0.1U 50V ±5% (RoHS)mylar capacitor 0.022uF 100V ±5% (RoHS)electrolytic cap. 1U 50V ±20% (RoHS)electrolytic cap. 100uF 16V ±20% (RoHS)electrolytic cap. 22U 50V ±20% (RoHS)electrolytic cap. 220U 10V ±20% (RoHS)electrolytic cap. 220U 16V ±20% (RoHS)electrolytic cap. 47U 25V ±20% (RoHS)mylar capacitor 0.022uF 100V ±5% (RoHS)electrolytic cap. 100uF 16V ±20% (RoHS)electrolytic cap. 6800U/50V ±20%D25X45mm (RoHS)141214232211212C116,C108,C113,C115,C119,C106,C139,C140,C107,C124,C125,C126,C128,C105,C112,C109,C117,C120,C114,C118,C129,C130,C111,C103,C123,C127,C110,C121,C122,Resistor 4.7K 1/4W ±5% CF 26mm (RoHS)Resistor 680Ω 1/4W ±5% CF 26mm (RoHS)Resistor 100Ω 1/6W ±5% CF 26mm (RoHS)Resistor 1K 1/6W ±5% CF 26mm (RoHS)Resistor 10K 1/6W ±5% CF 26mm (RoHS)Resistor 1M 1/6W ±5% CF 26mm (RoHS)Resistor 12K 1/6W ±5% CF 26mm (RoHS)Resistor 1.5K 1/6W ±5% CF 26mm (RoHS)Resistor 15K 1/6W ±5% CF 26mm (RoHS)Resistor 150K 1/6W ±5% CF 26mm (RoHS)Resistor 180Ω 1/6W ±5% CF 26mm (RoHS)Resistor 1.8K 1/6W ±5% CF 26mm (RoHS)Resistor 22K 1/6W ±5% CF 26mm (RoHS)Resistor 3.3K 1/6W ±5% CF 26mm (RoHS)Resistor 3.9K 1/6W ±5% CF 26mm (RoHS)Resistor 39K 1/6W ±5% CF 26mm (RoHS)Resistor 47Ω 1/6W ±5% CF 26mm (RoHS)Resistor 470Ω 1/6W ±5% CF 26mm (RoHS)Resistor 4.7K 1/6W ±5% CF 26mm (RoHS)Resistor 47K 1/6W ±5% CF 26mm (RoHS)Resistor 56Ω 1/6W ±5% CF 26mm (RoHS)Resistor 56K 1/6W ±5% CF 26mm (RoHS)Resistor 6.8K 1/6W ±5% CF 26mm (RoHS)Resistor 820Ω 1W ±5% 10mm (RoHS)Resistor 2.2Ω 1/2W ±5% 15mm (RoHS)Resistor 330Ω 2W ±5% 5mm(RoHS)cement Resistor 0.1Ω 5W ±5% (RoHS)semi-fixed Resistor 3K 0.3W ±20%(RoHS)2211112641213321413111111221R147,R150,R148,R151,R120,R124,R134,R143,R135,R139,R103,R123,R136,R137,141,R142,R118,R145,R152,R154,R131,R111,R114,R153,R128,R129,R133,R106,R107,R144,R105,R108,R126,R112,R113,R115,R116,R140,R110,R125,R130,R101,R117,R104,R109,R132,R127,R146,R149,R121,R122,R138,13
BALBOA series SUB10
Part NumberDescription
QtyReference DesignatorPOWER/MAIN PCB190-06m4558d-e192-021tip35c-e192-022tip36c-e192-201d882y-e192-202b772y-e192-027c1815gr-e192-991d669a-e192-992b649t-e197-00kbl405-e197-101n4002-eMiscellaneous171-udhss124d-e175-1c07v01-e175-1d02v01-e175-1d03v01-e193-3m2520-e323-AL-00020-0LAE351-AM03014A094-E352-AM03008D040-E361-FE-00051-0LAE361-NYL-00054-0LAERelay 5A 24V UDH-SS124D(RoHS)wire connector&base 7PIN PITCH=2.5mm (RoHS)wire connector&base 2PIN PITCH=3.96mm(RoHS)wire con&base 3 PIN PITCH=3.96mmJST-VH discard middle PINinsulation TO-3P 25x20mm (RoHS)HEAT SINK 65*32*31 ALM3*14 machine screw (RoHS)￠3*8 B ping screw (RoHS)transistor holder 14.2*8.0*5.2t=1.6mm (RoHS)transistor insulation (SW06002) (RoHS)1111211412RY101,P101,P102,P103,for Q107,Q108,I.C. OPA 4558D (RoHS) DUAL OP-AMP transistor TIP35C (RoHS) NPNtransistor TIP36C (RoHS) PNP*transistor KSD882Y (RoHS) NPN*transistor KSB772Y (RoHS) PNPtransistor 2SC1815GR TOSHIBA(RoHS) NPNtransistorHI-SINCERITY HSD669A(RoHS) NPNtransistor HSB649T (RoHS) PNPdiode 4A 500V KBL405(RoHS) BRIDGEdiode 1N4002TB (RoHS)1111121111U101,Q107,Q108,Q117,Q119,Q101,Q115,Q106,Q105,D110,D104,PREAMP PCBResistors110-16102j26-e110-16103j26-e110-16104j26-e110-16105j26-e110-16122j26-e110-16183j26-e110-16205j26-e110-16223j26-e110-16224j26-e110-16333j26-e110-16472j26-e110-16473j26-e110-16474j26-e110-16512j26-e116-161002f26-e116-161471f26-e116-161503f26-e116-161542f26-e116-162400f26-e116-162871f26-e116-163602f26-e116-165361f26-e116-1664r9f26-e116-166801f26-e116-168251f26-e115-h203b208-e115-h503a104-eCapacitors129-a104j633-e129-a153j633-emetalized cap. 0.1U 63V ±5% MSC (RoHS)metalized cap. 0.015U 63V MSC (RoHS)21C5,C215,C224,Resistor 1K 1/6W ±5% CF 26mm (RoHS)Resistor 10K 1/6W ±5% CF 26mm (RoHS)Resistor 100K 1/6W ±5% CF 26mm (RoHS)Resistor 1M 1/6W ±5% CF 26mm (RoHS)Resistor 1.2K 1/6W ±5% CF 26mm (RoHS)Resistor 18K 1/6W ±5% CF 26mm (RoHS)Resistor 2M 1/6W ±5% CF 26mm (RoHS)Resistor 22K 1/6W ±5% CF 26mm (RoHS)Resistor 220K 1/6W ±5% CF 26mm (RoHS)Resistor 33K 1/6W ±5% CF 26mm (RoHS)Resistor 4.7K 1/6W ±5% CF 26mm (RoHS)Resistor 47K 1/6W ±5% CF 26mm (RoHS)Resistor 470K 1/6W ±5% CF 26mm (RoHS)Resistor 5.1K 1/6W ±5% CF 26mm (RoHS)metal film Resistor 10K 1/6W ±1% MF 26mm (RoHS)metal film Resistor 1.47K 1/6W ±1% MF 26 mm (RoHS)metal film Resistor 150.0K 1/6W ±1% MF 26mm (RoHS)metal film Resistor 1/6W 15.4K 1% 26mm (RoHS)metal film Resistor 240Ω 1/6W ±1% MF 26 mm (RoHS)metal film Resistor 2.87k 1/6W ±1% MF 26 mm (RoHS)metal film Resistor 36K 1/6W ±1% MF 26mm (RoHS)metal film Resistor 5.36k 1/6W ±1% MF 26 mm (RoHS)metal film Resistor 64.9Ω1/6W ±1% MF 26 mm (RoHS)metal film Resistor 6.8K 1/6W ±1% MF 26mm (RoHS)metal film Resistor 8.25K 1/6W ±1% MF 26mm (RoHS)variable Resistor B20K (RoHS) CROSSOVERvariable Resistor D16 50K/1 A (RoHS) VOLUME5112113121121131112111112111R213,R214,R215,R254,R253,R212,R216,R217,R220,R221,R222,R225, R232,R235,R240,R228,R231,R266,R259,R264,R262,R226,R227,R257,R250,R255,R251,R249,R258,R260,R219,R252,R211,R229,R230,R7,R4,R1,R237,R238,R2,R234,R233,R6,R5,R224,R223,R3,VR202,VR201,14
BALBOA series SUB10
Part NumberDescription
QtyReference DesignatorPREAMP PCB129-a154j633-e129-a274j633-e129-a473j633-e129-a474j633-e129-a563j633-e130-2b221k503-e130-3f104z503-e130-ch220k503-e132-103j503-e135-3105m50-e135-3106m50-e135-3107m16-e135-3226m50-eSemiconductors192-027c1815gr-e197-031n4148-e199-15000515-e190-06m4558d-e190-16tl074cn-e195-10204hgw-eMiscellaneous162-50159201-e174-0rca326p-e180-tms7210v-e362-FE-00041-0LAEWIRE ASS'Y 2PIN 150mm white/red (RoHS)JACK RCA-326 (RoHS)SWITCH SLIDE 6PIN MS7210V (RoHS) PHASEPCB support 11.75*8.5*12.5H (RoHS)1111transistor 2SC1815GR TOSHIBA(RoHS) NPNdiode 100mA 75V SIGNAL 1N4148 ROHM (RoHS)zener diode 5.1V 1/2W 52mm (RoHS)I.C. OPA 4558D (RoHS) DUAL OP-AMP *I.C TL074CN ST (RoHS) QUAD OP-AMPtwo color LED 204HGW 3￠(RoHS)291121Q206,Q207,D201,D202,D118,D117,D207,D206,D211,D212,D214,D213,U203,U201,U202,D209,metalized cap. 0.15U 63V ±5% MSC (RoHS)metalized cap. 0.27uf 63V ±5% (RoHS)metalized cap. 0.047U 63V ±5% MSC (RoHS)metalized cap. 0.47U 63V ±5% MSC (RoHS)metalized cap. 0.056uF 63V ±5% MSC (RoHS)disc capacitor 220P 50V ±10% (RoHS)disc capacitor 0.1U 50V +80/-20% (RoHS)disc capacitor 22PF CH 50V±10% (RoHS)mylar capacitor 0.01uF 50V ±5% (RoHS)electrolytic cap. 1U 50V ±20% (RoHS)electrolytic cap. 10uF 50V ±20% (RoHS)electrolytic cap. 100uF 16V ±20% (RoHS)electrolytic cap. 22U 50V ±20% (RoHS)1112197111821C218,C216,C4,C221,C222,C217,C207,C208,C210,C211,C212,C214,C220, C230,C249,C232,C242,C244,C245,C246,C252,C254,C229,C223,C228,C206,C213,C219,C231,C241,C243,C251,C253C233,C234,C225,JK202,SW301,LIMITER PCBResistors110-16103j26-e110-16183j26-e110-16223j26-e110-16273j26-e110-16333j26-e110-16472j26-e110-16474j26-e110-16751j26-e110-16755j26-eCapacitors130-3f104z503-e132-103j503-e135-3226m50-e135-3476m25-eSemiconductors192-027c1815gr-e197-031n4148-e190-16tl074cn-etransistor 2SC1815GR TOSHIBA(RoHS) NPNdiode 100mA 75V SIGNAL 1N4148 ROHM (RoHS)*I.C TL074CN ST (RoHS) QUAD OP-AMP221Q301,Q302,D301,D302,U301,disc capacitor 0.1U 50V +80/-20% (RoHS)mylar capacitor 0.01uF 50V ±5% (RoHS)electrolytic cap. 22U 50V ±20% (RoHS)electrolytic cap. 47U 25V ±20% (RoHS)2221C305,C306,C302,C303,C301,C340,C304,Resistor 10K 1/6W ±5% CF 26mm (RoHS)Resistor 18K 1/6W ±5% CF 26mm (RoHS)Resistor 22K 1/6W ±5% CF 26mm (RoHS)Resistor 27K 1/6W ±5% CF 26mm (RoHS)Resistor 33K 1/6W ±5% CF 26mm (RoHS)Resistor 4.7K 1/6W ±5% CF 26mm (RoHS)Resistor 470K 1/6W ±5% CF 26mm (RoHS)Resistor 750Ω 1/6W ±5% CF 26mm (RoHS)Resistor 7.5M 1/6W ±5% CF 26mm (RoHS)812112121R301,R303,R304,R308,R309,R314,R340,R344R302,R310,R312,R341,R305,R342,R343,R307,R311,R313,R306,15
BALBOA series SUB10
Part NumberDescription
QtyReference DesignatorLIMITER PCBMiscellaneous162-50289001-e162-80098201-e175-9f40hr2-e104-tlx1100av-e CABLE ASS'Y wire 280mm AWG26 WHT (RoHS) 1 wire 90mm 28AWG (RoHS) 1SW301,wire connector&base 40PIN PITCH=2.54mm HR2*40 (RoHS) 0.15P301,PCB 4connectors (RoHS)0.25MISCELLANEOUS/MECHANICAL123-14j70d-eFerrite Core U-16.3*8.2*13(J70)+CASE (RoHS)130-3f472md00-edisc capacitor 4700P 400V ± 20% (RoHS)150-e8604107-ePower transformer EI-86 60Hz 120V TT0869906580152-u602015-epower line cord SVT FT-26FT (RoHS)154-u25006t0-efuse 2.5A 250V 20mm (RoHS)155-520020-eholder R3-11 (RoHS)162-10151001-eWIRE UL1617 150mm 22AWG BROWN 6:6 (RoHS)162-50652003-eWIRE 650mm RED=205# 0.5T BLK=110# 0.5T (RoHS)176-wjce1-ewire connector pin CE-1 (RoHS)180-prf1003s-ePower Switch ROCK RF-1003-BB2-OHA(RoHS)302-AL-05090-1LAErear board 300*200*2.5T BALBOA 120V (RoHS)306-ABS-00177-0BAErear housing 198*298*102mm (RoHS)311-ABS-00028-0BAEKnob 46077-W P.V.C.(RoHS)320-RUB-00033-0BAErubber foot pad 25*21*4t (RoHS)323-AL-00141-0LAEHEAT SINK 117.5*71.5*25 (RoHS) 333-EVA-00783-0BAEGASKET W 198*12*2.0T333-EVA-00807-0BAEGASKET L 274*12*2.0T (RoHS)333-EVA-00826-0BAEGASKET W 198*12*1.0T (RoHS)333-EVA-00835-0BAEGASKET L 274*12*1.0T (RoHS)333-SPG-00876-0BAEsphaeraster(SPG) 400*50*5T (RoHS)335-NYL-05015-0BAEwire clip SB4F-2 black (RoHS)337-CU-00101-0LAEmetal foil 65L*50W (RoHS)350-EM04012D024-E4￠*12 wood screw (RoHS)351-AM03008A079-EM3*8 machine screw (RoHS)351-HM04016A218-EM4*16 machine screw(RoHS)352-AM03008D040-E￠3*8 B ping screw (RoHS)352-AM03010D065-E￠3*10 P ping screw (RoHS)354-GM04002-EM4 nut with pad (RoHS)362-FE-00013-0LAEPCB support L TYPE t=1.6mmS.P.C.C 89*9*1.6T (RoHS)11111111111124122221214748142C00116
BALBOA series SUB10
17
BALBOA series SUB10 18
BALBOA series SUB10
19
BALBOA series SUB10
20
BALBOA series SUB10
21
BALBOA series SUB10
22
BALBOA series SUB10 23
BALBOA series SUB10 12FM phase swP112DFM phase sw123SW301A645 3 4 5 6C2520.1uF/C4C25110uF4C2440.1uF/CC24310uF8C246+15V0.1uF/C+15vDSW301BC208220PC2062110uF32R2115.1KD202C2074148R21210kR2236.8KU201ATL0741C2160.27uF/MSC9R2246.8KC2150.1uF/MSC10R22510KU201CTL0748R22618K3VR202AB20KC2180.15uF/MSC251R22718K6VR202BB20K41312U201DTL074141111U201TL074U202TL074U2034558-15v4-15VJK202A2G21R2131KC211220P1R21421KC210220PR21610K2C2170.056uF/MSCR22810K110K-15V+15v1R41.47K2R217D2014148C2540.1uF/C1C25310uFC2420.1uF/CC24110uFC2450.1uF/C220P31R2295.1kC219210uFR2305.1K3U202ATL074R231C220100K2A50KVR201R2342.87KC221C22265U202BTL0747C1JUPR23510KC2JUPR710KC50.1uF/MSCR38.25KC3JUPC40.047uF/MSCR2240R1150K910U202CTL074R564.921C2240.15uF/MSCR2381312U202DTL07414C22522uFR24010K220P118R23715.4K2C22KQ201OPT3R248OPT2C.47uF/MSC.47uF/MSCR23210kR23336K22+15VC21310uFC23110uFR2531kD213125.1VC230220PR2572M3D216JUP1Q207C18152R2604.7K1R22010kR65.36KR247OPT1C2230.01uF/MSCNot Present6U203B4558D7+15VD20622BJK202B3G311D212R22110KC214675220PC249TL074U201B21R22210k220PR25022K1R249233k+15v2D1174148C2281uFD11841482R251220KC229213U203A455822PD214124148R2541KR25522KR252470K22D215JUPQ206C181532R25814.7KR266100KC233115R259M201SGO7PTC6+15V54-15V3MUTE2GND1P2.5-7B12112R2151KR21947KC212220P41484148D2114148C234100uF2111-15V-15V0.1uF2414812D207R26218K1MR2641.2KC232100uFLED1FILENAME: ¡@PRE-AMPAREVISION: ¡@A/1ADRAWAPVDDSGNMODEL NO.¡@ BALBOA SUB10 BKCUSTOMER:¡@JBLDATE: 2006-09-20PAGE:¡@ 1 / 312345624
BALBOA series SUB10
25
BALBOA series SUB10
26
因篇幅问题不能全部显示，请点此查看更多更全内容